Write a 5-Minute Toolbox Talk for a Specific Trade Task on Site

You get a speakable 5-minute safety talk covering one task's top three hazards, ranked controls, pre-start checks, an open crew question and a sign-off line.

Prompt

Prompt
You are an experienced construction site safety coordinator who runs daily toolbox talks.

Your job: write a 5-minute toolbox talk for one specific trade task my crew is doing today. Before writing, ask me these questions in one message and wait for my answers:
1. What is the task and trade (e.g., cutting concrete block, working from a scissor lift)?
2. What site conditions apply today (weather, height, traffic, other trades nearby)?
3. Crew size and experience level?
4. Any recent near misses or incidents tied to this task?

Rules:
- Cover the top 3 hazards for this task only; skip generic filler that does not apply.
- List controls for each hazard in order: eliminate, engineer, admin, PPE, and include one check the crew can do before starting.
- Keep it speakable: short sentences, under 600 words, readable aloud in about 5 minutes.
- Ask one open crew question that makes people explain what they would do, not a yes/no question.
- Do not invent statistics, incident stories or regulation numbers.

Output format:
1. Title and task
2. Why this matters today (2-3 sentences)
3. Table: Hazard | What can happen | Controls | Pre-start check
4. Crew question
5. Key takeaway (one line)
6. Sign-off line with blanks for date, presenter and attendee names

End with one line reminding me to check this against local regulations, manufacturer instructions and site rules, and that it does not replace a qualified safety professional.

Example output

Example for: a masonry crew of 5 (two apprentices) cutting concrete block with a gas cut-off saw outdoors, windy morning, a near miss last week when a blade bound.

Toolbox Talk: Cutting Block with a Cut-Off Saw

Task: Dry and wet cutting of 8-inch concrete block at the east wall staging area.

Why this matters today

We had a blade bind last week that kicked the saw back toward Marco's leg. Today it is windy, so dust will travel toward the carpenters on the east side. Two of us are new to this saw.

Hazards and Controls
HazardWhat can happenControlsPre-start check
Kickback from blade bindingSaw jumps back at your body; deep cuts to legs or armsSupport block on both sides so the cut does not close; use the cutting station, not your knee; only trained operators run the saw; chaps, gloves, face shieldBlock sits flat on the stand, cut line overhangs, blade guard set
Silica dustBreathing fine dust that damages lungs over timeUse the water feed on every cut; position station downwind of other crews; respirator on when cuttingWater tank full and flowing at the blade before first cut
Damaged or wrong bladeBlade shatters or overheatsUse only the diamond blade rated for this saw's RPM; inspect after any bindNo cracks, missing segments or blue heat marks on the blade
Crew question

If the blade starts to pinch halfway through a cut, what exactly do you do with your hands and the saw, and why?

Key takeaway

Support the block, wet the cut, check the blade: every cut, every time.

Sign-off

I attended this talk and understand the controls for this task.

Date: __________ Presenter: __________

Attendees:






Check this talk against your local regulations, the saw manufacturer's instructions and site rules. It does not replace guidance from your site's competent person or a qualified safety professional.

Written by AI from this prompt. Your results will vary.

Tips and common edits

Why this works

  • Asking about site conditions and recent near misses makes the talk about today's job, not a generic safety lecture.
  • Ordering controls from elimination to PPE stops the talk from leaning only on gloves and glasses.
  • An open crew question forces people to explain their actions, which shows who actually understands the risk.

Use before a shift when your crew starts a higher-risk task. Have the task, today's site conditions and any recent near misses ready. Works in ChatGPT, Claude or Gemini; print or read from your phone.

Common edits

  • Ask for a Spanish or bilingual version for a mixed-language crew.
  • Shorten it to a 2-minute version with only the single biggest hazard.

Prompt details

By
Prompts-GPT editors
Published

Did this prompt work?

Keep exploring

More in Career & Job Search